PROFIBUS PA / FOUNDATION™ Fieldbus transmitter

6350A

Linearized temperature measurement with RTD or TC sensor.
Difference, average or redundancy temperature measurement with RTD or TC sensor.
Converts analog mA signals into digital values on the bus communication.
Linear resistance, potentiometer and bipolar mV measurement.

Bus transmitter with both PROFIBUS PA and FOUNDATION Fieldbus communication. A unique switch function ensures automatic shift between the two protocols.
Set-up for PROFIBUS PA can be done via Siemens Simatic^® PDM^®, ABB Melody / Harmony and Metso DNA software and for FOUNDATION Fieldbus via Emerson DeltaV, Yokogawa CS 1000 / CS 3000, ABB Melody / Harmony and Honeywell Experion software.
Built-in simulation mode function.
Polarity-independent bus connection.
24 bit A/D converter ensures high resolution.
PROFIBUS PA function blocks:
2 analog.
FOUNDATION Fieldbus function blocks:
2 analog and 1 PID.
FOUNDATION Fieldbus capability:
Basic or LAS.

Mounted vertically or horizontally on a DIN rail. Using the 2-channel version up to 84 channels per meter can be mounted.

Supply
Supply voltage	9.0...32 VDC
Power dissipation, per channel	< 11 mA
Isolation voltage
Test voltage	1.5 kVAC for 60 s
Working voltage	50 VRMS / 75 VDC
Response time
Response time (programmable)	1...60 s
Warm-up time	30 s
Signal / noise ratio	Min. 60 dB
Accuracy	Better than 0.05% of selected range
Updating time	< 400 ms
Execution time, PID controller	< 200 ms
Execution time, analog input	< 50 ms
Signal dynamics, input	24 bit
EMC immunity influence	< ±0.1% of reading
Extended EMC immunity: NAMUR NE21, A criterion, burst	< ±1% of reading

RTD input
RTD type	Pt25…1000, Ni25…1000, Cu10…1000, lin. R, potentiometer
Cable resistance per wire	50 Ω (max.)
Sensor current	Nom. 0.2 mA
Effect of sensor cable resistance (3-/4-wire)	< 0.002 Ω / Ω
Sensor error detection	Yes
Short circuit detection	< 15 Ω
Linear resistance input
Linear resistance min....max.	0 Ω...10000 Ω
Potentiometer input
Potentiometer min....max.	10 Ω...100 kΩ
TC input
Thermocouple type	B, E, J, K, L, N, R, S, T, U, W3, W5
Cold junction compensation (CJC)	< ±0.5°C
Sensor error detection	Yes
Sensor error current: When detecting / else	Nom. 2 μA / 0 μA
Short circuit detection	< 3 mV
Bipolar current input
Measurement range	-100…+100 mA
Input resistance	10 Ω + PTC < 20 Ω
Cable breakage detection (4...20 mA)	< 0.3 mA
Bipolar mV input
Measurement range	-800…+800 mV
Min. measurement range (span)	2.5 mV
Input resistance	10 MΩ
Short circuit detection	< 3 mV

PROFIBUS PA connection
PROFIBUS PA protocol	Profile A&B, ver. 3.0
PROFIBUS PA protocol standard	EN 50170 vol. 2
PROFIBUS PA address (at delivery)	126
PROFIBUS PA function blocks	2 analog
FOUNDATION Fieldbus connection
FOUNDATION Fieldbus protocol	FF protocol
FOUNDATION Fieldbus protocol standard	FF design specifications
FOUNDATION Fieldbus version	ITK 4.6
FOUNDATION Fieldbus capability	Basic or LAS
FOUNDATION Fieldbus function blocks	2 analog and 1 PID