Programmable transmitter

5114B

The 5114 transmitter can be configured using the PReset software and the Loop Link communications unit.

Jumper selectable inputs for current/voltage or temperature.
Programmable current (0...100 mA) and voltage (0...250 VDC) inputs.
Linearized, electronic temperature measurement.
Conversion of linear resistance variation e.g, from solenoids and butterfly valves or linear movements with attached potentiometer.
17.1 VDC loop and 2.5 VDC potentiometer supplies.
Automatic 4- / 3-wire or programmable 2-wire cable compensation.
Configurable sensor error detection including NAMUR NE43.

Active or Passive current output and selectable voltage output.
Separation of circuits in PELV/SELV installations.
I.S. barrier for temperature sensors, potentiometers, and current / voltage signals.
I.S. barrier with I.S. power supply for 2-wire transmitters in zone 0, 1, 2, 20, 21 and 2.

Supply
Supply voltage, universal	21.6...253 VAC, 50...60 Hz or 19.2...300 VDC
Fuse	400 mA SB / 250 VAC
Max. required power	2.1 W / 2.8 W (1 / 2 ch.)
Isolation voltage
Isolation voltage, test / working	3.75 kVAC / 250 VAC
PELV/SELV	IEC 61140
Response time
Temperature input, programmable (0...90%, 100...10%)	400 ms...60 s
mA / V input (programmable)	250 ms...60 s
Auxiliary supplies
2-wire supply (pin 44...42 and 54...52)	28...17.1 VDC / 0...20 mA
Programming	Loop Link
Signal / noise ratio	Min. 60 dB (0...100 kHz)
Accuracy	Better than 0.05% of selected range
Updating time	115 ms (temperature input) 75 ms (mA / V / mV input)
Signal dynamics, input	22 bit
Signal dynamics, output	16 bit
Auxiliary voltages: Reference voltage	2.5 VDC ±0.5% / 15 mA
EMC immunity influence	< ±0.5% of span
Extended EMC immunity: NAMUR NE21, A criterion, burst	< ±1% of span

Common input specifications
Max. offset	50% of selected max. value
RTD input
RTD type	Pt100, Ni100, lin. R
Cable resistance per wire	10 Ω (max.)
Sensor current	Nom. 0.2 mA
Effect of sensor cable resistance (3-/4-wire)	< 0.002 Ω / Ω
TC input
Thermocouple type	B, E, J, K, L, N, R, S, T, U, W3, W5, LR
Cold junction compensation (CJC)	< ±1.0°C
Sensor error current	Nom. 30 μA
Sensor error detection	Yes
Current input
Measurement range	0...100 mA
Min. measurement range (span)	4 mA
Input resistance: Supplied unit	Nom. 10 Ω + PTC 10 Ω
Input resistance: Non-supplied unit	RSHUNT = ∞, VDROP < 6 V
Voltage input
Measurement range	0...250 VDC -150...+150 mV
Min. measurement range (span)	5 mV
Input resistance	Nom. 10 MΩ (≤ 2.5 VDC) Nom. 5 MΩ (> 2.5 VDC) Nom. 10 MΩ (mV input)

Current output
Signal range	0...20 mA
Min. signal range	10 mA
Load (@ current output)	≤ 600 Ω
Load stability	≤ 0.01% of span / 100 Ω
Current limit	≤ 28 mA
Sensor error indication	Programmable 0...23 mA
NAMUR NE43 Upscale/Downscale	23 mA / 3.5 mA
Passive 2-wire mA output
Signal range	4...20 mA
Load stability	≤ 0.01% of span / 100 Ω
Max. load resistance [Ω]	(Vsupply-3.5)/0.023 A
Max. external 2-wire supply	29 VDC
Effect of external 2-wire supply voltage variation	< 0.005% of span / V
Voltage output
Signal range	0...10 VDC
Min. signal range	500 mV
Load (@ voltage output)	≥ 500 kΩ
of span	= of the presently selected range