Universal transmitter

4116

Programmable via detachable display front (4501), process calibration, signal and relay simulation, password protection, error diagnostics and selection of help text in several languages.

Linearized, electronic temperature measurement with RTD or TC sensor.
Conversion of linear resistance variation to a standard analog current / voltage signal, i.e. from solenoids and butterfly valves or linear movements with attached potentiometer.
Power supply and signal isolator for 2-wire transmitters.
Process control with 2 pairs of potential-free relay contacts and analog output.
Galvanic separation of analog signals and measurement of floating signals.
The 4116 is designed according to strict safety requirements and is therefore suitable for application in SIL 2 installations.

When 4116 is used in combination with the 4501 display / programming front, all operational parameters can be modified to suit any application. As the 4116 is designed with electronic hardware switches, it is not necessary to open the device for setting of DIP-switches.
A green / red front LED indicates normal operation and malfunction. A yellow LED is ON for each active output relay.
Continuous check of vital stored data for safety reasons.
4-port 2.3 kVAC galvanic isolation.

Supply
Supply voltage, universal	21.6...253 VAC, 50...60 Hz or 19.2...300 VDC
Fuse	400 mA SB / 250 VAC
Max. required power	≤ 2.5 W
Isolation voltage
Isolation voltage, test / working	2.3 kVAC / 250 VAC
Response time
Temperature input (0...90%, 100...10%)	≤ 1 s
mA / V input (0...90%, 100...10%)	≤ 400 ms
Auxiliary supplies
2-w. supply (term. 44...43)	25...16 VDC / 0...20 mA
Programming	PR 45xx
Signal / noise ratio	Min. 60 dB (0...100 kHz)
Accuracy	Better than 0.1% of sel. range
EMC immunity influence	< ±0.5% of span
Extended EMC immunity: NAMUR NE21, A criterion, burst	< ±1% of span

RTD input
RTD type	Pt10/20/50/100/200/250; Pt300/400/500/1000; Ni50/100/120/1000; Cu10/20/50/100
Cable resistance per wire	50 Ω (max.)
Sensor current	Nom. 0.2 mA
Effect of sensor cable resistance (3-/4-wire)	< 0.002 Ω / Ω
Sensor error detection	Yes
Short circuit detection	< 15 Ω
Linear resistance input
Linear resistance min....max.	0 Ω...10000 Ω
Potentiometer input
Potentiometer min....max.	10 Ω...100 kΩ
TC input
Thermocouple type	B, E, J, K, L, N, R, S, T, U, W3, W5, LR
Cold junction compensation (CJC) via ext. sensor in 5910	20...28°C ≤ ±1°C, -20...20°C / 28...70°C ≤ 2°C
CJC via int. mounted sensor	±(2.0°C + 0.4°C * Δt)
Δt =	Internal temp.-ambient temp.
Sensor error detection	Yes
Sensor error current: When detecting / else	Nom. 2 μA / 0 μA
Current input
Measurement range	0...20 mA
Programmable measurement ranges	0...20 and 4...20 mA
Input resistance	Nom. 20 Ω + PTC 50 Ω
Sensor error detection: Loop break 4...20 mA	Yes
Voltage input
Measurement range	0...12 VDC
Programmable measurement ranges	0/0.2...1, 0/1...5, 0/2...10 VDC
Input resistance	Nom. 10 MΩ

Current output
Signal range	0...20 mA
Programmable signal ranges	0...20/4...20/20...0/20...4 mA
Load (@ current output)	≤ 800 Ω
Load stability	≤ 0.01% of span / 100 Ω
Sensor error indication	0 / 3.5 / 23 mA / none
NAMUR NE43 Upscale/Downscale	23 mA / 3.5 mA
Output limitation, on 4...20 and 20...4 mA signals	3.8...20.5 mA
Output limitation, on 0...20 and 20...0 mA signals	0...20.5 mA
Current limit	≤ 28 mA
Voltage output
Signal range	0...10 VDC
Programmable signal ranges	0/0.2...1; 0/1...5 ; 0/2...10; 1...0.2/0; 5...1/0; 10...2/0 V
Load (@ voltage output)	≥ 500 kΩ
Relay output
Relay functions	Setpoint, Window, Sensor error, Latch, Power and Off
Max. voltage	250 VRMS
Max. current	2 AAC or 1 ADC
Max. AC power	500 VA

FM	3025177
UL	UL 508 / C22.2 no. 14
DNV-GL Marine	Stand. f. Certific. No. 2.4
EU RO Mutual Recognition Type Approval	MRA000000Z
SIL	Hardware assessed for use in SIL applications