Prodotti 0
4104
 
 

4104

 

Universal uni-/bipolar signal transmitter

 

  1. Overview +

  2. Technical details +

  3. Accessories +


Application

  • Fast < 20 ms response time for measuring signals produced by torque, position, current & acceleration sensors.
  • User configurable bipolar or unipolar I/O means the 4104 is suitable for nearly any voltage or current conversion.
  • The excitation source enables measurement of two or three wire transmitters.
  • The active or passive I/O makes the 4104 perfect for power matching current loops.
  • Converts narrow bipolar inputs to wide bipolar or unipolar outputs, e.g., ±1 volt input = ±10 volt or 4...20 mA output.
  • Selectable direct or inverse I/O makes the 4104 suitable for proportional control applications.
  • The ”V-curve” function outputs 100% – 0 – 100% when a 0 – 100% input signal is present.

Technical characteristics

  • The latest analog and digital techniques are used to obtain maximum accuracy and immunity to interference.
  • The current output can drive up to 800 Ohms, with an adjustable response time of 0.0…60.0 seconds.
  • Exceptional mA output load stability of < 0.001% of span/100 Ohm.
  • Meets the NAMUR NE21 recommendations, ensuring high accuracy in harsh EMC environments.
  • Meets the NAMUR NE43 recommendations, allowing the control system to easily detect a sensor error.
  • Each unit is tested to a high 2.3 kVAC, 3-port galvanic isolation level.
  • Excellent signal to noise ratio of > 60 dB.

Mounting / installation / programming

  • Very low power consumption means units can be mounted side by side without an air gap – even at 60°C ambient temperature.
  • Approved for marine applications.
  • Programming, monitoring, and 2-point process calibration is accomplished with the 4501 detachable display.
  • All programming can be password protected.

Environmental Conditions

  • Operating temperature

    -20°C to +60°C

  • Storage temperature

    -20°C to +85°C

  • Calibration temperature

    20...28°C

  • Relative humidity

    < 95% RH (non-cond.)

  • Protection degree

    IP20

  • Installation in

    Pollution degree 2 & meas. / overvoltage cat. II

Mechanical specifications

  • Dimensions (HxWxD)

    109 x 23.5 x 104 mm

  • Dimensions (HxWxD) w/ 4501/4511

    109 x 23.5 x 116 / 131 mm

  • Weight approx.

    250 g

  • DIN rail type

    DIN EN 60715/35 mm

  • Wire size

    0.13...2.08 mm2 AWG 26...14 stranded wire

  • Screw terminal torque

    0.5 Nm

  • Vibration

    IEC 60068-2-6

  • 2...13.2 Hz

    ±1 mm

  • 13.2...100 Hz

    ±0.7 g

Common specifications

  • Supply

  • Supply voltage, universal

    21.6...253 VAC, 50...60 Hz or 19.2...300 VDC

  • Max. required power

    ≤ 2.5 W

  • Internal power dissipation

    ≤ 2.0 W

  • Isolation voltage

  • Isolation voltage, test / working

    2.3 kVAC / 250 VAC

  • Response time

  • Response time (0...90%, 100...10%)

    < 20 ms

  • Auxiliary supplies

  • 2-wire loop supply

    > 16 V / 20 mA

  • 3-wire loop supply

    > 18 V / 20 mA

  • Loop supply limitation

    30 mA

  • Programming

    Communication enabler 4511 / Programming front 4501

  • Signal / noise ratio

    > 60 dB

  • Accuracy

    Better than 0.05% of selected range

  • Cut-off frequency (3 dB)

    > 40 Hz

  • EMC immunity influence

    < ±0.5% of span

  • Extended EMC immunity: NAMUR NE21, A criterion, burst

    < ±1% of span

Input specifications

  • Current input

  • Signal range

    ±23 mA

  • Programmable measurement ranges

    0...20 and 4...20 mA

    ± 10 and ± 20 mA

  • Input voltage drop

    1.4 V @ 20 mA

  • Loop error detection, 4...20 mA: Low

    < 3.6 mA

  • Loop error detection, 4...20 mA: High

    > 21 mA

  • Voltage input

  • Signal range

    ±12 V

  • Programmable measurement ranges

    0/0.2...1, 0/1...5, 0/2...10 VDC

    ±1, ±5 and ±10 V

  • Input resistance

    > 2 MΩ

Output specifications

  • Current output

  • Signal range

    0...23 mA (unipolar)

    -23...+23 mA (bipolar)

  • Current limit

    ≤ 28 mA (unipolar)

    ± 28 mA (bipolar)

  • Load stability

    ≤ 0.001% of span / 100 Ω

  • Response time, programmable

    0.0...60.0 s

  • Output limitation, on 4...20 and 20...4 mA signals

    3.8...20.5 mA

  • Output limitation, on other unipolar mA signals

    0 and 115% of max. value

  • Output limitation, on bipolar mA signals

    ±115% of min. & max. values

  • Sensor error indication, at 4...20 mA input: selectable

    Low, High, Zero, None

  • Active unipolar and bipolar mA output

  • Programmable ranges

    0...20 and 4...20 mA

    ±10 and ±20 mA

    Direct or Inverted Action

  • V-curve function, active signals, 100-0-100%

    20-0-20 mA

  • Load (@ current output)

    ≤ 800 Ω

  • Passive 2-wire mA output

  • Programmable ranges

    0...20 and 4...20 mA

    Direct or Inverted action

  • V-curve function, 100-0-100%

    20-0-20 mA

  • External loop supply

    3.5 - 26 V

  • Voltage output

  • Programmable signal ranges

    0/0.2...1; 0/1...5 ; 0/2...10 V

    ±1, ±5 and ±10 V

    Direct or Inverted action

  • V-curve function, 100-0-100%

    1-0-1, 5-0-5 and 10-0-10 V

  • Load (@ voltage output)

    ≥ 500 kΩ

  • Response time, programmable

    0.0...60.0 s

  • Output limitation - outside range: on unipolar V signals starting from 0

    0 and 115% of max. value

  • Output limitation - outside range: on unipolar V signals with offset

    -5% of min. value and 115% of max. value

  • Output limitation - outside range: on bipolar V signals

    ±115% of min. & max. values

  • Sensor error indication, at 4...20 mA input: selectable

    Low, High, Zero, None

Observed authority requirements

  • EMC

    2014/30/EU

  • LVD

    2014/35/EU

  • EAC

    TR-CU 020/2011

Approvals

  • UL

    UL 508 / C22.2 no. 14

  • FM

    3025177

  • DNV-GL Marine

    Stand. f. Certific. No. 2.4

La vostra richiesta è stata inviata con successo - 0 Prodotti nella tua lista
Descrizione del prodotto Quantità
Si prega di specificare la variante (si veda il datasheet) – oppure indicare “variante sconosciuta”
I vostri contatti
Continua a navigare
Nessun prodotto aggiunto alla vostra lista…
Nessun prodotto nella vostra lista…

Mentre consultate le pagine sui prodotti presenti sul nostro sito web, avete la possibilità di aggiungere i nostri prodotti alla lista – ed inviarci tale lista per richiedere una quotazione. Per aggiungere i prodotti alla lista, cliccate sul pulsante “RICHIEDI UN PREVENTIVO” presente su ciascuna delle pagine sui prodotti.

Una volta inoltrata la lista, provvederemo a ricontattarvi quanto prima.

Se non desiderate inoltrare tale lista, essa rimarrà comunque visibile alla vostra attenzione sul sito web per 7 giorni (tramite “cookie” sul vostro PC o tablet)




Ci auguriamo troviate utili tali funzionalità. Si prega di andare alle pagine sui prodotti per aggiungere i nostri prodotti alla lista
Grazie per la vostra richiesta
Provvederemo quanto prima a ricontattarvi telefonicamente o via e-mail.