Du har inga produkter på listan…
När du ser dig omkring bland produkterna på vår hemsida har ni möjlighet att lägga till produkter i en lista och skicka denna lista till oss och därmed begära en offert. Du kan lägga till produkter i listan genom att klicka på ”Få en enkel offert”- knappen på de enskilda produktsidorna.
När du har skickat listan kommer vi att återkoppla till dig så snart som möjligt.
Om du inte skickar listan kommer den att vara synlig på webbplatsen i 7 dagar (vi kommer att använda oss av ”cookies” på din dator eller surfplatta)
Vi hoppas att ni finner denna funktion användbar. Gå till produktsidorna för att lägga till produkter i din lista.

4104
Universal uni-/bipolar signal transmitter
- Measures and outputs uni-/bipolar voltage and current signals
- Works with both passive and active inputs and outputs
- Uses the 4501 display for programming and process monitoring
- Fast < 20 ms response time and excellent < 0.05% accuracy
- Universally powered by 21.6…253 VAC / 19.2...300 VDC
Application
- Fast < 20 ms response time for measuring signals produced by torque, position, current & acceleration sensors.
- User configurable bipolar or unipolar I/O means the 4104 is suitable for nearly any voltage or current conversion.
- The excitation source enables measurement of two or three wire transmitters.
- The active or passive I/O makes the 4104 perfect for power matching current loops.
- Converts narrow bipolar inputs to wide bipolar or unipolar outputs, e.g., ±1 volt input = ±10 volt or 4...20 mA output.
- Selectable direct or inverse I/O makes the 4104 suitable for proportional control applications.
- The ”V-curve” function outputs 100% – 0 – 100% when a 0 – 100% input signal is present.
Technical characteristics
- The latest analog and digital techniques are used to obtain maximum accuracy and immunity to interference.
- The current output can drive up to 800 Ohms, with an adjustable response time of 0.0…60.0 seconds.
- Exceptional mA output load stability of < 0.001% of span/100 Ohm.
- Meets the NAMUR NE21 recommendations, ensuring high accuracy in harsh EMC environments.
- Meets the NAMUR NE43 recommendations, allowing the control system to easily detect a sensor error.
- Each unit is tested to a high 2.3 kVAC, 3-port galvanic isolation level.
- Excellent signal to noise ratio of > 60 dB.
Mounting / installation / programming
- Very low power consumption means units can be mounted side by side without an air gap – even at 60°C ambient temperature.
- Approved for marine applications.
- Programming, monitoring, and 2-point process calibration is accomplished with the 4501 detachable display.
- All programming can be password protected.
Environmental Conditions
Operating temperature | -20°C to +60°C |
Storage temperature | -20°C to +85°C |
Calibration temperature | 20...28°C |
Relative humidity | < 95% RH (non-cond.) |
Protection degree | IP20 |
Installation in | Pollution degree 2 & meas. / overvoltage cat. II |
Mechanical specifications
Dimensions (HxWxD) | 109 x 23.5 x 104 mm |
Dimensions (HxWxD) w/ 4501/4511 | 109 x 23.5 x 116 / 131 mm |
Weight approx. | 250 g |
DIN rail type | DIN EN 60715/35 mm |
Wire size | 0.13...2.08 mm2 AWG 26...14 stranded wire |
Screw terminal torque | 0.5 Nm |
Vibration | IEC 60068-2-6 |
2...13.2 Hz | ±1 mm |
13.2...100 Hz | ±0.7 g |
Common specifications
Supply |
|
Supply voltage, universal | 21.6...253 VAC, 50...60 Hz or 19.2...300 VDC |
Max. required power | ≤ 2.5 W |
Internal power dissipation | ≤ 2.0 W |
Isolation voltage |
|
Isolation voltage, test / working | 2.3 kVAC / 250 VAC |
Response time |
|
Response time (0...90%, 100...10%) | < 20 ms |
Auxiliary supplies |
|
2-wire loop supply | > 16 V / 20 mA |
3-wire loop supply | > 18 V / 20 mA |
Loop supply limitation | 30 mA |
Programming | Communication enabler 4511 / Programming front 4501 |
Signal / noise ratio | > 60 dB |
Accuracy | Better than 0.05% of selected range |
Cut-off frequency (3 dB) | > 40 Hz |
EMC immunity influence | < ±0.5% of span |
Extended EMC immunity: NAMUR NE21, A criterion, burst | < ±1% of span |
Input specifications
Current input |
|
Signal range | ±23 mA |
Programmable measurement ranges |
0...20 and 4...20 mA
± 10 and ± 20 mA |
Input voltage drop | 1.4 V @ 20 mA |
Loop error detection, 4...20 mA: Low | < 3.6 mA |
Loop error detection, 4...20 mA: High | > 21 mA |
Voltage input |
|
Signal range | ±12 V |
Programmable measurement ranges |
0/0.2...1, 0/1...5, 0/2...10 VDC
±1, ±5 and ±10 V |
Input resistance | > 2 MΩ |
Output specifications
Current output |
|
Signal range |
0...23 mA (unipolar)
-23...+23 mA (bipolar) |
Current limit |
≤ 28 mA (unipolar)
± 28 mA (bipolar) |
Load stability | ≤ 0.001% of span / 100 Ω |
Response time, programmable | 0.0...60.0 s |
Output limitation, on 4...20 and 20...4 mA signals | 3.8...20.5 mA |
Output limitation, on other unipolar mA signals | 0 and 115% of max. value |
Output limitation, on bipolar mA signals | ±115% of min. & max. values |
Sensor error indication, at 4...20 mA input: selectable | Low, High, Zero, None |
Active unipolar and bipolar mA output |
|
Programmable ranges |
0...20 and 4...20 mA
±10 and ±20 mA Direct or Inverted Action |
V-curve function, active signals, 100-0-100% | 20-0-20 mA |
Load (@ current output) | ≤ 800 Ω |
Passive 2-wire mA output |
|
Programmable ranges |
0...20 and 4...20 mA
Direct or Inverted action |
V-curve function, 100-0-100% | 20-0-20 mA |
External loop supply | 3.5 - 26 V |
Voltage output |
|
Programmable signal ranges |
0/0.2...1; 0/1...5 ; 0/2...10 V
±1, ±5 and ±10 V Direct or Inverted action |
V-curve function, 100-0-100% | 1-0-1, 5-0-5 and 10-0-10 V |
Load (@ voltage output) | ≥ 500 kΩ |
Response time, programmable | 0.0...60.0 s |
Output limitation - outside range: on unipolar V signals starting from 0 | 0 and 115% of max. value |
Output limitation - outside range: on unipolar V signals with offset | -5% of min. value and 115% of max. value |
Output limitation - outside range: on bipolar V signals | ±115% of min. & max. values |
Sensor error indication, at 4...20 mA input: selectable | Low, High, Zero, None |
Observed authority requirements
EMC | 2014/30/EU |
LVD | 2014/35/EU |
EAC | TR-CU 020/2011 |
Approvals
UL | UL 508 / C22.2 no. 14 |
FM | 3025177 |
DNV-GL Marine | Stand. f. Certific. No. 2.4 |

4501
Display / programming front
4511
Communication enabler
4590
ConfigMate
8510
8 unit 4511 Modbus cable
8511
4511 Y-splitter Modbus cable
8513
RJ45 Modbus termination
8514
3 X RJ45 female Y-splitter
8515
RJ45 female to female cable adapter
8516
RJ45 female to female shielded cable adabter