Items 0
3112
 
 

3112

 

Pt100 converter - isolated

 

  • Excellent accuracy, better than 0.05% of span
  • Slimline housing of 6 mm
  • Excellent EMC performance and 50/60 Hz noise suppression
  • Selectable < 30 ms / 300 ms response time
  • Pre-calibrated temperature ranges selectable via DIP-switches
  1. Overview +

  2. Technical details +

  3. Accessories +


Application

  • The 3112 temperature converter measures a standard 2-, 3- or 4-wire Pt100 temperature sensor, and provides an isolated analog voltage or current output.
  • High 3 port isolation provides surge suppression and protects the control system from transients and noise.
  • The 3112 can be mounted in the safe area or in Zone 2 / Division 2 areas.
  • Approved for marine applications.

Technical characteristics

  • Flexibly powered by 24 VDC (±30%) via power rail or connectors.
  • < 30 ms fast response time with simultaneous sensor error detection when selected.
  • Selectable 300 ms response time when signal dampening is needed.
  • Excellent conversion accuracy in all available ranges, better than 0.05% of span.
  • Meeting the NAMUR NE21 recommendations, the 3112 provides top measurement performance in harsh EMC environments.
  • The device meets the NAMUR NE43 standard defining out of range and sensor error output values.
  • A visible green LED indicates operational status of the unit and the input sensor.
  • All terminals are protected against overvoltage and polarity error.
  • High galvanic isolation of 2.5 kVAC.
  • Excellent signal/noise ratio of > 60 dB.

Mounting / installation / programming

  • Selectable DIP-settings for easy configuration of more than 1000 factory calibrated measurement ranges.
  • The narrow 6 mm housing allows up to 165 units to be mounted per meter of DIN rail, without any air gap between units.
  • Wide ambient temperature range of -25...+70°C.

Environmental Conditions

  • Operating temperature

    -25°C to +70°C

  • Storage temperature

    -40°C to +85°C

  • Calibration temperature

    20...28°C

  • Relative humidity

    < 95% RH (non-cond.)

  • Protection degree

    IP20

  • Installation in

    Pollution degree 2 & meas. / overvoltage cat. II

Mechanical specifications

  • Dimensions (HxWxD)

    113 x 6.1 x 115 mm

  • Weight approx.

    70 g

  • DIN rail type

    DIN EN 60715/35 mm

  • Wire size

    0.13 x 2.5 mm2 / AWG 26...12 stranded wire

  • Screw terminal torque

    0.5 Nm

  • Vibration

    IEC 60068-2-6

  • 2...25 Hz

    ±1.6 mm

  • 25...100 Hz

    ±4 g

Common specifications

  • Supply

  • Supply voltage

    16.8...31.2 VDC

  • Max. required power

    0.70 W

  • Max. power dissipation

    0.70 W

  • Isolation voltage

  • Isolation voltage, test / working

    2.5 kVAC / 300 VAC (reinforced)

  • Zone 2 / Div. 2

    250 VAC

  • Response time

  • Response time (0...90%, 100...10%)

    < 30 ms / 300 ms (selectable)

  • Accuracy

    Better than 0.05% of selected range

  • Signal / noise ratio

    Min. 60 dB

  • Programming

    DIP-switches

  • Signal dynamics, input

    23 bit

  • Signal dynamics, output

    18 bit

  • EMC immunity influence

    < ±0.5% of span

  • Extended EMC immunity: NAMUR NE21, A criterion, burst

    < ±1% of span

  • Incorrect DIP-switch setting identification

    0 V / 0 mA output; LED 0.5 s / 1 Hz

Input specifications

  • RTD input

  • Temperature range, Pt100

    -200...+850°C

  • Min. measurement range (span)

    10°C

  • Accuracy: the greater of

    Better than 0.05% of span or 0.1°C

  • Temperature coefficient: the greater of

    0.02°C/°C or ≤ ±0.01%/°C

  • Sensor current

    < 150 µA

  • Sensor cable resistance

    < 50 Ω per wire

  • Effect of sensor cable resistance (3-/4-wire)

    < 0.002 Ω / Ω

  • Sensor error detection

    Yes - selectable via DIP-switch

  • Broken sensor detection

    > 800 Ω

  • Shorted sensor detection

    < 18 Ω

Output specifications

  • Common output specifications

  • Updating time

    10 ms

  • Current output

  • Signal range

    0...23 mA

  • Programmable signal ranges

    0 / 4...20 mA

  • Sensor error indication (0...20 mA)

    0 mA or 23 mA / OFF

  • Sensor error indication (4...20 mA)

    3.5 mA or 23 mA / acc. to NAMUR NE43 or OFF

  • Load (@ current output)

    ≤ 600 Ω

  • Load stability

    ≤ 0.01% of span / 100 Ω

  • Current limitation @ low output load

    < 60 mA peak / < 4 mA average

  • Voltage output

  • Programmable signal ranges

    0/1...5 and 0/2...10 V

  • Sensor error indication

    0 V / 10% above the max. / none

  • Open output

    < 18 V

I.S. / Ex marking

  • ATEX

    II 3 G Ex nA IIC T4 Gc

  • IECEx

    Ex nA IIC T4 Gc

  • FMus

    Cl. I, Div. 2, Gp. A, B, C, D T4 or Cl. I, Zone 2, AEx nA IIC T4

  • FMca

    Cl. I, Div. 2, Gp. A, B, C, D T4 or Cl. I, Zone 2, Ex nA IIC T4

Observed authority requirements

  • EMC

    2014/30/EU

  • LVD

    2014/35/EU

  • RoHS

    2011/65/EU

  • EAC

    TR-CU 020/2011

Approvals

  • ATEX 2014/34/EU

    KEMA 10ATEX0147 X

  • IECEx

    KEM 10.0068X

  • FM

    FM17US0004X / FM17CA0003X

  • DNV-GL Marine

    Stand. f. Certific. No. 2.4

  • UL

    UL 61010-1

Your request has been sent successfully. - 0 Items on your list
Product description Quantity
Please specify variant(s) (see data sheet) - or indicate ‘Variant unknown’
Your contact information
Continue browsing
No products added
You have no products on your list...

When browsing product pages on this website, you have the possibility to add products to a list - and send your list to us, thereby requesting a quotation.
You add products to the list by clicking the "GET A QUOTE" button on the individual product pages.

When you have submitted the list, we will get back to you as quickly as possible.

If you don't submit the list, it will be visible to you on the website for 7 days (we will place a so-called' cookie on your pc or tablet).

We hope you will find the functionality useful. Go to the product pages to add products to your list.
Thank you for your request for a quotation.
We will get back to you by phone or email as soon as possible.