Name: Universal transmitter 4116
Rating: 5.0 (2 reviews)

4116

Linearized, electronic temperature measurement with RTD or TC sensor.
Conversion of linear resistance variation to a standard analog current / voltage signal, i.e. from solenoids and butterfly valves or linear movements with attached potentiometer.
Power supply and signal isolator for 2-wire transmitters.
Process control with 2 pairs of potential-free relay contacts and analog output.
Galvanic separation of analog signals and measurement of floating signals.
The 4116 is designed according to strict safety requirements and is therefore suitable for application in SIL 2 installations.
Suitable for the use in systems up to Performance Level “d” according to ISO-13849.

When 4116 is used in combination with the 45xx display / programming units, all operational parameters can be modified to suit any application. As the 4116 is designed with electronic hardware switches, it is not necessary to open the device for setting of DIP-switches.
A green / red front LED indicates normal operation and malfunction. A yellow LED is ON for each active output relay.
Continuous check of vital stored data for safety reasons.
4-port 2.3 kVAC galvanic isolation.

Very low power consumption means units can be mounted side by side without an air gap – even at 60°C ambient temperature.
Configuration, monitoring, 2-point process calibration and more are accomplished using PR's 45xx detachable displays.
All programming can be password-protected.

Supply
Supply voltage, universal	21.6...253 VAC, 50...60 Hz or 19.2...300 VDC
Fuse	400 mA SB / 250 VAC
Max. required power	≤ 2.5 W
Max. power dissipation	≤ 2.5 W
Isolation voltage
Test voltage	2.3 kVAC
Working voltage	250 VAC (reinforced) / 500 VAC (basic)
Response time
Temperature input (0...90%, 100...10%)	≤ 1 s
mA / V input (0...90%, 100...10%)	≤ 400 ms
Auxiliary supplies
2-w. supply (term. 44...43)	25...16 VDC / 0...20 mA
Programming	PR 4500 communication interfaces
Signal dynamics, input	24 bit
Signal dynamics, output	16 bit
Signal / noise ratio	Min. 60 dB (0...100 kHz)
Accuracy	Better than 0.1% of sel. range
EMC immunity influence	< ±0.5% of span
Extended EMC immunity: NAMUR NE21, A criterion, burst	< ±1% of span

RTD input
RTD type	Pt10/20/50/100/200/250; Pt300/400/500/1000; Ni50/100/120/1000; Cu10/20/50/100
Cable resistance per wire	50 Ω (max.)
Sensor current	Nom. 0.2 mA
Effect of sensor cable resistance (3-/4-wire)	< 0.002 Ω / Ω
Sensor error detection	Yes
Short circuit detection	< 15 Ω
Linear resistance input
Linear resistance min....max.	0 Ω...10000 Ω
Potentiometer input
Potentiometer min....max.	10 Ω...100 kΩ
TC input
Thermocouple type	B, E, J, K, L, N, R, S, T, U, W3, W5, LR
Cold junction compensation (CJC) via ext. sensor in 5910	20...28°C ≤ ±1°C, -20...20°C / 28...70°C ≤ 2°C
CJC via int. mounted sensor	±(2.0°C + 0.4°C * Δt)
Sensor error detection	Yes
Sensor error current: When detecting / else	Nom. 2 μA / 0 μA
Current input
Measurement range	0...23 mA
Programmable measurement ranges	0...20 and 4...20 mA
Input resistance	Nom. 20 Ω + PTC 50 Ω
Sensor error detection: Loop break 4...20 mA	Yes
Voltage input
Measurement range	0...12 VDC
Programmable measurement ranges	0/0.2...1, 0/1...5, 0/2...10 VDC
Input resistance	Nom. 10 MΩ

Current output
Signal range	0...23 mA
Programmable signal ranges	0...20/4...20/20...0/20...4 mA
Load (@ current output)	≤ 800 Ω
Load stability	≤ 0.01% of span / 100 Ω
Sensor error indication	0 / 3.5 / 23 mA / none
NAMUR NE43 Upscale/Downscale	23 mA / 3.5 mA
Output limitation, on 4...20 and 20...4 mA signals	3.8...20.5 mA
Output limitation, on 0...20 and 20...0 mA signals	0...20.5 mA
Current limit	≤ 28 mA
Voltage output
Signal range	0...10 VDC
Programmable signal ranges	0/0.2...1; 0/1...5 ; 0/2...10; 1...0.2/0; 5...1/0; 10...2/0 V
Load (@ voltage output)	≥ 500 kΩ
Relay output
Relay functions	Setpoint, Window, Sensor error, Latch, Power and Off
Max. voltage	250 VAC / VDC
Max. current	2 A
Max. AC power	500 VA
Max. DC current, resistive load > 30 VDC	See manual for details